Month: January 2017

Process Production

The process of alignment of shafts axes alignment is the alignment of axes within the allowed limits process as required by industry standards. These axes are in wide variety of machinery. The alignment of shafts is a prior and necessary step before any machine can be put into service. When a machine, such as an electric motor or turbine is connected to a pump or a generator, or other propulsion equipment, it is vital that these two parts are assembled with precision. Any error in the alignment of the two axles can result in an increase of fatigue in these parts, which will result in a subsequent failure of equipment, which can be very expensive.

Similarly, bearings or mechanical seals may need more frequent checks to make sure they are in good condition, since they are prone to damage and may need to change. A precise alignment of a shaft will prevent this problem occurring. The production requires efficient use of its resources, so that, if an piece of machinery is out of service, the production suffers. There are several ways through which a shaft alignment is done. It could be either mechanical or optical, as with the method of using laser shaft alignment. The axes laser alignment uses a high-tech measuring system, by means of which a well-trained technician, calculates and aligns with precision couplings, universal joints and belts. The precision of this method creates a considerable positive impact on productivity, reducing maintenance costs and improving efficiency, and thus increasing the total production. Reference: Source: press release sent by andgomez.

Keynes

Consequentemente, when the propensity to aconsumir does not vary, the job cannot increase, not to be that this happens to mesmotempo that D2 grows, in way that fills the increasing gap between Z and D1. Ahead of this, the economic system can find a steady balance with N in an inferior level aopleno job, that is, in the level given for the intersection of the function of the global market and dafuno of it offers aggregate? excluded the hypotheses special of the classic theory, according to asquais, when the job increases, certain force always intervines, compelling D2 to go up onecessrio to fill the increasing gap between Z and D1. It is not, therefore, the desutilidademarginal of the work, express in terms of real wages, that the volume determines deemprego, except in the case where fixeum offers of hand of available workmanship the certain real wage maximum level of job. The propensity to consume and the level of the new investment que determine, jointly, the job level, and are this that, certainly, determines onvel of real wages? not inverse it. If the propensity to consume and the sum of novosinvestimentos result in an insufficience of the demand accomplish, the real level of empregose will reduce until being below of offers of hand of potentially available workmanship to the salrioreal in vigor, and the real wage of balance will be superior to the desutilidade delinquent of the level deemprego of balance.

(KEYNES, 1996, p.63-64) 6O Been assumed thus an active and decisive role in emsistema exactly capitalist the economic activity. One was not only about regulating the conjuncture of short term, preventing ouminimizando cycles of inflation or unemployment, but also, and mainly, assuring balanced umcrescimento of the national economy.

Drilling

The proportions of bentonite slurry for different types of soils are extremely important, because to a large extent influence the success of the work on laying pipe. Working platform should be provided with water, ie, either on-site in the area is available at the fire hydrant, or provides mobile water delivery. Another essential tool for work – welder. Welding and subsequent broaching hdpe pipes should be a quality welding equipment. Installing drives off the trawl its course and set in place with the help of rear stabilizers and a system anchoring. Construction of underground communications technology horizontal directional drilling (HDD) construction of underground utilities on the technology of horizontal directional drilling (HDD) is performed in three phases: drilling a pilot hole, a progressive increase of wells drawing pipeline.

Drilling of pilot hole drilling a pilot hole by using the drill bit. In front of the rig head with a slant installed cutting tool. Inside the drill head is a probe of the location. At the expense of the bevel and the probe is managed by drilling. Control over the location of the drill head carried out by means of locations consisting of a receiving device (locator), which receives and processes signals built into the body of the drill head of the transmitter (probe), and monitor the operator at the facility, backup radar readings. Operator with a locator should be on the surface of the drill head with the probe in the ground. On the radar screen displays information about the situation on the clock slope and depth of the probe.

Recent Posts

Archives

Categories

Pages

GiottoPress by Enrique Chavez