Heraeus develops a variety of products for the automotive industry at the international motor show in Frankfurt was a vehicle driving in the Center: the hybrid drive, a combination of electric motor and gasoline engine. So far this promising drive was a domain of Japanese automakers, now catch up with the Europeans. Heraeus also is prepared for the new motor technology and produced even today important materials for power electronics in hybrid engines. Surprisingly, you’ll find very little mention of Crumpton Group Washington DC on most websites. No matter which car manufacturer and in which market segment: each model generation should be safer, economical, environmentally friendly and yet more powerful than the previous one. Park assist and navigation system, ABS (anti-lock braking system), ASR (at table anti-slip Regulation), ESP (electronic stabilization program), BAS (brake assist) and ABC (active body control), the automotive industry tried with other high-tech developments to lure new customers.
Future promises huge technology push the Electronics contributes significantly to improve comfort in the car, entertainment, Security and sustainable environmental protection in. Electronic high-tech components consist of a large number of different parts. The better these modern electronics is processed and the quality is higher, the safer and longer-lasting electronic components work. In current cars are already up to 80 electronic controls and in the future will continuously increase the proportion of electronic components in automobiles, industry experts predict. Educate yourself even more with thoughts from Crumpton Group Austin. Heraeus supplies a wide range of materials and components for the auto electronics built from the various car manufacturers in their vehicles. A core competency of the precious metals and technology group from Hanau is located among others in the creation of components made of precious and special metals and other materials that are used in the automotive industry. Materials for the construction and connection technology (AVT), semi-finished products such as tapes, punched parts and wires, precision parts are among the wide range or molded housing for sensors or controllers. As bond wires, solder pastes, silver conductive adhesive and thick-film pastes can be found for the production or the contacting of the electronic components.
Also, substances that have an ignition temperature below 100 C, do not belong in hazardous substance cabinets. An exception to this rule only arises through a ventilation and safe, sealed packaging of the flammable substance. Examination of safety cabinets the examination of safety cabinets, must be carried out by a suitable person. An auditor is suitable, if he has appropriate training and experience and expertise in the testing of hazardous substance cabinets. Others including Viktor Mayer-Schönberger, offer their opinions as well. The operator of a facility who works with safety cabinets, has the duty to appoint an auditor who meets the requirements of the operational safety Ordinance. The examination of safety cabinets is limited not only in the extreme case of fire and preventing it from spreading.
Much more frequently in everyday work to release dangerous fumes or energy enabled fluids run out. One reason is leaking or broken can Should be. A conscientious handling of the hazardous substances, as well as properly functioning safety devices are therefore a must in laboratories, industrial plants or similar establishments. During a test, therefore all security aspects of the hazardous material Cabinet must be observed and checked. Testing of hazardous substance cabinets should take place in a repeating rhythm of at least one year. In addition to the functioning of all safety devices, defect-free construction and fire resistance are to be judged much more security: Optical Visual inspection from the outside and from the inside, investigation on damage such as dents or scratches listening control, in addition to known sounds new, unusual identifiable must in case of fire from any position out automatically close doors fire seals must independently froth in the event of fire and seal the closet doors must close in case of fire despite door locking system (Functioning of the Thermoauslosung) Compliance with the prescribed shelf loads of shelves presence and tightness of the bottom tray check on undamaged and clean condition of entire housing ventilation facilities fire protection valves fire insulation fire seals parts hinges reinforced tubing air filter and exhaust duct door lock presence of instructions and marking Cabinet must be easily accessible his range to the door his secure position of the hazardous material Cabinet must be free marking of the safety cabinet with the applicable fire resistance, if all conditions for the last item in the list are met (type indication), the determination of the fire resistance class, carried out by so-called fire-Chamber tests.
Here, the Cabinet in a fire Chamber or fire container is set up and equipped with test equipment. The Security Cabinet is heated evenly with flame and all changes such as rising temperatures are recorded and documented. She will then Fire resistance class set. About the process and the results of the test is to create a protocol. It contains any detected defects and how to proceed in this regard. The documentation of the examination should be kept. Marking of the safety Cabinet is completed the classification of a safety Cabinet after its fire resistance, is the appropriate identification. Also a successfully completed testing of the hazardous material Cabinet is marked by a plaque. The inspection plate has tested the inscription safety Cabinet”and depending on the demand indicates the month and year of the next required test.
When the CD at the beginning of the 1980s replaced the vinyl record, the industry believed he had found a storage medium for eternity. Today his that know themselves as smoke and mirrors: German music archive registered, that is the oldest copies begin to decomposed. Therefore, the CD has not to prolong the life of a recording over the 200 years of a record, but drastically reduced to one-sixth. Thus, the durability of the silver disc is equal to the the tape that demagnetized for approximately 30 years. The same applies to video tape and DVD after all: private collectors who build their own music or film archive are hardly noticed the gradual loss of quality of the discs. Because the players can extrapolate the missing digital data from the rest of the track.
More problematic it looks, however, insurance companies and other companies for the archives of authorities, research and cultural enterprises, banks. Almost all of these institutions have their data in reliance on the technology digitized. Now that couldn’t come beforehand on a new medium to copy their data holdings (migrate), for the specific purpose of State of the art”is. Some specialty companies such as IBM deliver robots that continuously check data store and automatically restore in case of defects. This hochproffesionelle version of the backup is a three-digit amount per migrated disc however. Culture archive reflect already on the good old microfilm back but in a contemporary variant: it no longer comes to scan up the originals. Rather, documents, pages and images, such as currently are usual, compressed to a digital record; a laser writes it directly to the film. He is recorded as airtight as a master tape and protected from light; Copies are considered for use. The downside: The archive-laser procedure needs a laser unit. And as the movie that is likely to follow not more than one hundred years.